Any OSx86 installation guide can seem daunting at first glance, especially when trying to remember cryptic terminal commands and sorting through volumes of misinformation on the web. This guide requires no coding, terminal work, or Mac experience of any kind. You will not need access to a Mac. In fact, it's easier and faster for me to install Snow Leopard with fully working components on my system than it is to install Windows 7. And more fun.
The

The quick version goes like this: Boot into the Snow Leopard installer, format the hard drive you want to install Snow Leopard to (go to Utilities - Disk Utility, then click on the drive, select. Mac OS X Snow Leopard (version 10.6) is the seventh major release of macOS, Apple's desktop and server operating system for Macintosh computers. Snow Leopard was publicly unveiled on June 8, 2009 at Apple’s Worldwide Developers Conference.

iBoot + MultiBeast method is designed and tested for any desktop or laptop running the latest line of Intel processors, the Core i3/i5/i7s. I have had reports of success with older machines as well including CoreDuo, Core2Duo, and even Pentium 4. However, AMD processors are not supported.

YOU WILL NEED

• A computer running an Intel Processor
• A blank CD
• A Mac OS X Snow Leopard Retail DVD
• To leave any fear of your computer at the door.
• Patience and humility- it may not work out perfectly the first time- but with enough tenacity and grit, you'll reach the promised land. It's easy to get frustrated, but don't give up! There are a community of users with similar hardware in the tonymacx86 Forum to provide support if you get stuck.

BEFORE YOU BEGIN

• Use only 1 graphics card in the 1st PCIe slot with 1 monitor plugged in.
• Remove any hard drives besides the blank drive being used for OS X.
• Remove any USB peripherals besides keyboard and mouse.
• Remove any PCI cards besides graphics- they may not be Mac compatible.
• It's best to use an empty hard drive- you will have to partition and format the drive.
• Always back up any of your important data.

STEP 1: BIOS SETTINGS
You will need to set your BIOS to ACHI mode and your Boot Priority to boot from CD-ROM first. This is the most important step, and one many people overlook. Make sure your bios settings match these. It's not difficult- the only thing I did on my Gigabyte board besides setting Boot Priority to CD/DVD first was set Optimized Defaults, change SATA to AHCI mode, and set HPET to 64-bit mode.

STEP 2: INSTALL MAC OS X
In order to boot the Mac OS X Retail DVD, you'll need to download and burn. For desktops and laptops using unsupported Intel CPUs and graphics, a legacy version of iBoot can be downloaded here. If you have an Ivy Bridge or Haswell system, you can’t use the default iBoot. Use iBoot Ivy Bridge or iBoot Haswell.

1. Download iBoot
2. Burn the image to CD
3. Place iBoot in CD/DVD drive
4. Restart computer
5. At boot prompt, eject iBoot
   
   
   
6. Insert your Mac OS X Snow Leopard Retail DVD and press F5
7. When you see the screen below, press enter to begin the boot process
8. When you get to the installation screen, open Utilities/Disk Utility. NOTE: If you cannot get to the installation screen, retry from Step 4, type PCIRootUID=1 before hitting enter. If that doesn't work then try PCIRootUID=1 -x or just -x which will enter Mac OS X Safe Mode and will allow you to proceed. For some graphics cards, use GraphicsEnabler=No boot flag to proceed.
9. Partition your hard drive to GUID Partition Table
10. Format your hard drive to Mac OS Extended (Journaled). NOTE: The bootloader can only boot from a disk or partition of 1 TB or less. Partition larger drives.
11. For the purposes of this guide, name it Snow Leopard. You can rename it later.
12. Close Disk Utility
13. When the installer asks you where to install, choose Snow Leopard
14. Choose Customize‚ and uncheck additional options. This will hasten the install process. You can always install this stuff later.
15. Restart computer.
16. Place iBoot back in drive.
17. When you get to the boot selection screen, choose your new Snow Leopard installation.
18. View the super-cool Mac OS X Snow Leopard Welcome Video, and set up your computer!

STEP 3: UPDATE TO 10.6.8
If you have a Sandy Bridge system, please follow these specialized instructions to update to 10.6.8.

1. Open Finder and navigate to your Snow Leopard drive.
2. Download the Mac OS X 10.6.8 Combo Update
3. Download MultiBeast
4. Open MultiBeast- don't run it yet, just leave it open. Set up windows as shown.
5. Mount MacOSXUpdCombo10.6.8.dmg
6. Install MacOSXUpdCombo10.6.8.pkg
7. Upon completion, the installer will ask you to reboot. DO NOT REBOOT.
8. Switch to the already open MultiBeast. If it closes, just re-open it.

STEP 4: MULTIBEAST
MultiBeast is an all-in-one post-installation tool designed to enable boot from hard drive, and install support for Audio, Network, and Graphics. It contains two different complete post-installation solutions: EasyBeast and UserDSDT. In addition it includes System Utilities to rebuild caches and repair permissions and a collection of drivers, boot loaders, boot time config files and handy software.
Choose one of the following options directly following a fresh installation and update:
EasyBeast is a DSDT-free solution for any Core/Core2/Core i system. It installs all of the essentials to allow your system to boot from the hard drive. Audio, Graphics and Network will have to be enabled separately.
UserDSDT is a bare-minimum solution for those who have their own pre-edited DSDT. Place your DSDT.aml on the desktop before install. Audio, Graphics and Network will have to be enabled separately. HINT: Check the DSDT Database for a pre-edited DSDT.

1. Run MultiBeast.
2. If you have a custom DSDT that's been edited, place the file on your desktop and choose UserDSDT.
3. All others select EasyBeast
4. Select System Utilities.
5. Optionally, you may install further drivers via Advanced Options to enable ethernet, sound, graphics, etc... Be sure to read the documentation provided about each installation option. NOTE:EasyBeast, and UserDSDT install the bootloader by default, so you'll not need to check that option.
MultiBeast Demo Videos
6. Install to Snow Leopard- it should take about 4 minutes to run scripts.
7. Eject iBoot.
8. Reboot- from your new Snow Leopard installation drive.

Congratulations! You're done!!
Your PC is now fully operational, while running the latest version of Mac OS X Snow Leopard! And you have a nice Boot CD to get into your system in case things go awry. Boot your system from iBoot if you have issues. You may run MultiBeast as often as you like.
If you can't boot, try typing -x at the boot prompt to enter safe mode, or just boot with iBoot. When you get to the desktop, you can make all of the changes you need to. The best way to start fresh is delete whatever you're trying to get rid of- including the whole /Extra folder, as most kexts are installed there. Then you can re-run MultiBeast. As long as you rebuild caches and repair permissions after you're done, you can do just about anything you want to /Extra/Extensions and /System/Library/Extensions. Anything can be tweaked and enabled upon subsequent uses of MultiBeast.
If you've had success using iBoot + MultiBeast, consider a contribution to help keep the sites going. We're constantly updating and tweaking our tools to help you.
Thanks in advance!
-tonymacx86 & MacMan
For our most current workarounds and solutions forissues such as USB and audio, check out the Mac OS X 10.6.3 Update, Mac OS X 10.6.4 Update,Mac OS X 10.6.5 Update, Mac OS X 10.6.6 Update, Mac OS X 10.6.7 Update, and Mac OS X 10.6.8 Updatearticles. Good luck, and see you on the forum!
Related Posts: Dual Boot Windows 7 and OS X Snow Leopard

The steps below will guide you through how to Install OS X Snow Leopard from a USB Flash Drive. Alternatively, you can also read these instructions on how to install OS X Lion from a USB Flash Drive.

Apple officially released Snow Leopard a couple years ago and consumers can still find the latest version of OS X at Apple Stores and resellers across the country.

At version 10.6, Snow Leopard, focused more on improving speed and performance than adding new features to OS X. With the operating system available to customers, individuals are ready for their upgrades.

Installing OS X From a USB Drive

Like other versions of OS X, Snow Leopard can be installed from a USB drive. This is especially beneficial to Macbook Air users looking to install the OS without a DVD drive. To do this, you’ll need to prepare your USB drive with the installation files. Like many of our other Mac Help articles, the steps listed below worked particularly for Snow Leopard but should also work for installing OS X from USB on Leopard.

Install Snow Leopard From Disc

The installation files sit at 6.2gb on the Snow Leopard DVD, so you’ll probably need a drive that has at least 8gb available. If you want your installation files to last against the elements, check out this 8 GB Water/Shock Resistant USB flash drive.

After you’ve gotten the correct USB device, connect it to your Mac and prepare it with the Snow Leopard installation files by following these steps:

NOTE:Depending on your flash drive, you may need to follow steps 5 – 7 on installing onto a USB drive to make sure the drive is bootable before you get start. This includes updating the options for the partition so that it is set to a GUID partition. If the USB drive is not bootable you will NOT be able to install from it.

1. Open Disk Utility and select the Flash Drive
2. Select the Erase tab on the right and then set Format to Mac OS Extended (Journaled). Name the partition you’ll be creating Snow Leopard or OS X Install so you can keep track of your installation device. After you’ve done this, click the Erase button.
3. After Disk Utility finishes erasing your old data on the flash drive and setting it as a new partition, it will be ready for the Snow Leopard install files. Select the Restore tab at the top and then drag the Snow Leopard DVD to the Source field. Select your USB device for the Destination file. Click Restore and wait for the restoration to finish (about 20 minutes).
4. If the restoration worked correctly you should be able to open your USB device and see the Leopard installation files. If you try and click the Install OS X Snow Leopard icon, you’ll get the message below telling you you can’ install OS X from this volume. IGNORE the message. The next steps will walk you through the installation steps.
5. Now that the installation files are successfully on your USB device, be sure to remove the Snow Leopard installation DVD from your drive. Next, restart your Mac and when it first starts to reboot, be sure to hold down the option (alt) key on your keyboard. After a few seconds at least two volumes should appear for you to select from for installation. One of those will be the USB drive we just prepared. Select it.
6. After the Snow Leopard installation software boots from your USB drive, follow the on screen instructions for installation. It took about 38 minutes to install Snow Leopard on my machine from the USB drive. I’m curious to see how this compares to the average Mac users, please leave a post in the comments letting us know how long it took on your machine.
7. After the installation finishes, it will reboot your computer into your new upgraded version of OS X, version 10.6 Snow Leopard

Can You Install Snow Leopard Without A Disk

This method works for installing OS X Snow Leopard onto a Mac from a USB Drive. It should also work for installing Leopard or other older versions of OS X on Intel Based Macs. Check back often for additional help and tips for your Mac.

Make Snow Leopard Install Disk From Dmg